Texas Instruments
La imagen puede ser una representación.
Consulte las especificaciones para obtener detalles del producto.
TPA4860DR
Ver Detalle Hojas de datos

TPA4860DR

Product Overview

Category: Integrated Circuit (IC)

Use: Audio Amplifier

Characteristics: - High-performance audio amplifier - Class D amplifier architecture - Wide supply voltage range - Low distortion and noise - Efficient power consumption

Package: PowerPAD SOIC

Essence: TPA4860DR is a high-performance audio amplifier IC designed for various audio applications. It offers excellent sound quality, low distortion, and efficient power consumption.

Packaging/Quantity: TPA4860DR is available in a PowerPAD SOIC package. The quantity per package may vary depending on the supplier.

Specifications

  • Supply Voltage Range: 4.5V to 15V
  • Output Power: Up to 10W
  • Efficiency: >90%
  • Total Harmonic Distortion (THD): <0.1%
  • Signal-to-Noise Ratio (SNR): >100dB
  • Operating Temperature Range: -40°C to +85°C

Detailed Pin Configuration

The TPA4860DR IC has the following pin configuration:

  1. VDD: Power supply voltage input
  2. GND: Ground reference
  3. IN+: Positive audio input
  4. IN-: Negative audio input
  5. SD: Shutdown control input
  6. OUT: Amplified audio output
  7. PGND: Power ground reference
  8. PVDD: Power supply voltage input

Functional Features

  • High-quality audio amplification with low distortion and noise
  • Class D amplifier architecture for improved efficiency
  • Wide supply voltage range allows flexibility in various applications
  • Shutdown control for power-saving mode
  • Thermal and short-circuit protection

Advantages and Disadvantages

Advantages: - High-performance audio amplification - Efficient power consumption - Low distortion and noise - Wide supply voltage range

Disadvantages: - Limited output power compared to higher wattage amplifiers - Requires external components for complete audio system integration

Working Principles

The TPA4860DR is a Class D audio amplifier that utilizes pulse-width modulation (PWM) techniques to amplify audio signals efficiently. It converts the input audio signal into a high-frequency square wave, which is then filtered and amplified to produce the desired audio output.

The Class D architecture allows for high efficiency by minimizing power dissipation in the output stage. This results in reduced heat generation and improved overall power consumption.

Detailed Application Field Plans

The TPA4860DR is suitable for various audio applications, including but not limited to:

  1. Portable audio devices
  2. Home theater systems
  3. Automotive audio systems
  4. Multimedia speakers
  5. Gaming consoles
  6. Professional audio equipment

Its compact size, high-quality audio reproduction, and efficient power consumption make it an ideal choice for these applications.

Detailed and Complete Alternative Models

  1. TPA4861DR: Similar to TPA4860DR with higher output power capability.
  2. TPA4862DR: Similar to TPA4860DR with additional features like built-in equalization and volume control.
  3. TPA4863DR: Similar to TPA4860DR with enhanced thermal management capabilities.

These alternative models offer different specifications and features to cater to specific application requirements.

Note: The above information is based on the available data at the time of writing and may be subject to change. It is recommended to refer to the official datasheet for the most accurate and up-to-date information.

Word Count: 470 words

Enumere 10 preguntas y respuestas comunes relacionadas con la aplicación de TPA4860DR en soluciones técnicas

Sure! Here are 10 common questions and answers related to the application of TPA4860DR in technical solutions:

  1. Q: What is TPA4860DR? A: TPA4860DR is a class-D audio amplifier integrated circuit (IC) designed for high-power audio applications.

  2. Q: What is the maximum power output of TPA4860DR? A: The maximum power output of TPA4860DR is typically around 20 Watts per channel into an 8-ohm load.

  3. Q: Can TPA4860DR operate with a single power supply? A: Yes, TPA4860DR can operate with a single power supply ranging from 4.5V to 26V.

  4. Q: Does TPA4860DR require any external components for operation? A: Yes, TPA4860DR requires external components such as input and output capacitors, resistors, and inductors for proper operation.

  5. Q: What is the efficiency of TPA4860DR? A: TPA4860DR has a high efficiency of up to 90%, making it suitable for battery-powered applications.

  6. Q: Can TPA4860DR handle low-impedance loads? A: Yes, TPA4860DR can drive loads as low as 4 ohms, making it compatible with a wide range of speakers.

  7. Q: Is TPA4860DR protected against overtemperature and short circuits? A: Yes, TPA4860DR features built-in thermal shutdown and short-circuit protection to ensure safe operation.

  8. Q: Can TPA4860DR be used in automotive applications? A: Yes, TPA4860DR is suitable for automotive applications as it can operate over a wide temperature range and has built-in protection features.

  9. Q: What is the input voltage range of TPA4860DR? A: The input voltage range of TPA4860DR is typically between 1V and 2V, making it compatible with various audio sources.

  10. Q: Does TPA4860DR support stereo or mono operation? A: TPA4860DR can be configured for both stereo and mono operation, providing flexibility in system design.

Please note that these answers are general and may vary depending on the specific application and implementation of TPA4860DR.